When we put wallpapers, we generally encounter problems such as this. In particular, most of the friends who would like to do their very own wallpapers are a lot more than they wish, and lastly they will find that there are always some little flaws.
In fact, provided that the construction is taken care of, these problems could be avoided. Today, we will choose these problems and concentrate on solving them!
Base film peeling
1) Before brushing the base film, check if the wall is standard, no powder, no floating coating.
2) Is there a slight crack in the wall structure?
3) Whether the construction temperature is above 5 degrees.
4) Brush the bottom film too thick when it is first, and brush the next one when it’s not dry. Because of the difference in drying time taken between the inner and outer layers, it may cause peeling.
5) Whether the foundation film is too thick, can be relieved by adding drinking water. After polishing with sandpaper, re-brush the base film.
The treatment of the bottom film includes a great influence on the wallpaper effect, and the most direct effect may be the stability of the wallpaper. Therefore, the bottom film should be handled in accordance with the requirements of the guidelines, combined with the actual situation.
Glue overflow
Glue overflow is a common phenomenon in the process of wallpapering. Through the construction process, try to avoid the glue overflowing the wallpaper surface area through the paper tape. The rubber surface wallpaper is relatively easy to clean. You can use all the wallpaper except the rubber tape wallpaper. Paper tape building is recommended.
1) Wipe with a damp sponge for a surface area washable wallpaper.
2) Use a dry towel to eliminate it, suitable for wallpapers that cannot be stained on the top.
3) Absorbed with a wet sponge, ideal for wallpapers with contaminants on the surface.
There are signs at the joint seam
The handling of wallpaper seams has always been a key part of wallpaper construction, and many professional construction masters have their own tips. For the layman, pay special attention to the construction. When the wallpaper was used, the glue didn’t completely hurry out and piled-up at the seams. The glue reacted with the wallpaper for a long time.
Alternative: 60-80 degrees boiling water a small bottle, plus a bottle of white vinegar, wait for the drinking water to cool down, squat in the seam. (Recommended for partial screening), the wallpaper will last better in 1-2 months, and 80% of the traces could be removed.
Wallpaper shrinking
The phenomenon of wallpaper shrinkage is mainly caused by the workers’ lack of strict seams during construction, that leads to this problem in the later stage, which is related to the construction technology of the workers. Because the wallpaper is made of wood pulp, it gets the characteristics of hardwood swelling and shrinking, the performance isn’t particularly stable, there will be a certain expansion following the glue is finished, and shrinkage occurs through the drying process. Although the expansion is uncontrollable, workers can control shrinkage during building.
Most 43171070734 943761297a of the wallpaper shrinks are invisible unless the joints aren’t enough. In this case, it is generally better reserve a coincident part at the joint. Generally, it is preferable that the joint overlaps at 1-3 cm.
If shrinkage has already occurred, the Mica Wallpapers repair process is relatively simple. Make use of a wet towel dampened with drinking water to soak the seam for ten minutes, and use the edge of the wallpaper knife to pick the wallpaper, that may usually be found. If the attachment on the surface of the wallpaper is a steel surface, it is easy to make the top of wallpaper tarnish and dark after scraping, and it is not really recommended to operate.
Wallpaper moldy
1) The wallpaper is moldy and generally offers spots on the top of wallpaper.
(1) The wall ought to be inspected for water seepage.
(2) Whether the glue is completely dry.
(3)When wallpaper is normally applied, whether moisture and air are present in the wallpaper for a long time, react with the glue to trigger mold.
(4) The elements is humid.
(5) The wallpaper is wet.
Moldy wallpaper is definitely a problem that individuals who are wallpapering are worried about. It is also probably the most difficult problems to solve after emergence. As a result, this kind of problem should be based on prevention. It is advisable to work before moisture and moisture.
Then, after the wallpaper offers such problems, is there no solution? of course not.
2) Processing method
(1) The mildew is small. It is suggested to wipe with water or detergent and blow dry with a locks dryer.
(2) Bleaching water is simple to irritate the skin and may cause the wallpaper to fade. It isn’t recommended.
(3) If the mold is large, the wallpaper must be replaced. If the wall is seepage, it’s important to completely resolve the problem before posting.